Replacing Lock on uPVC Door To replace the lock, you need to first remove the screw holes and handle. This is usually easy to do. The next step is to find the screw which holds the lock barrel in place. This screw is usually colored differently than the other screws and located at the top of the faceplate. Remove the Cylinder The first step in changing the lock on a door made of upvc is to take off the current lock cylinder from the door. This is a simple process that can be done in around 30 minutes. All you require is a screwdriver. The Euro Cylinder screw is normally located on the inside of the door, next to the lock cylinder. The screw should be easy to identify as it is usually different in colour from the other screws. Remove this screw and keep it in a safe place. After removing the cylinder you can begin to remove the handle. To do this, you will have to open the door wide enough that you can see the inside edge of the door, as well as the side of lock faceplate. Remove the screw that holds the handle to the door by using the screwdriver. Once the screw is removed you can pull the handle towards you and take the rest of it off the door. If you're having trouble getting the handle off the door frame, you may have to take it off. You can use a screwdriver or drill to remove the handle. Be careful not to strip or cross-thread it. When you are ready to replace your cylinder, ensure that it's the right size for your door. Cylinders are measured according to two measurements: (a) the distance from the center of the Fixing Screw hole to the bottom of the cylinder and (b) the distance between the keyhole and the edge of the lock plate. Take the handle off The good news is that the moment your upvc handle starts to become stiff, floppy or loose, it's an easy issue to fix. The multipoint lock cylinder, or other internal parts within the door, in between the handle and the frame, are often the reason. Weather conditions, heavy use or aging can cause upvc locks to wear. This could lead to problems with the closing and locking mechanisms of the door. If the cylinder has been damaged, it can be difficult to turn the key, and the lock could become stiff, causing the handle to drop. This can be fixed by replacing the cylinder, which is a straightforward process. It is possible to complete this yourself, although some knowledge of the mechanism will be required. The first step is to remove the handle which will permit you to access the cylindrical and replace it with a brand new one. To accomplish this, you will need a screwdriver as well as tape measure. You will need to determine the size of the cylinder you have, because it will allow you in locating a replacement that fits correctly. The cylinder is what allows you to lock the upvc door. It is important to order an alternative that is identical in size. To get rid of the old cylinder you will have to unscrew all the screws that hold it. Be careful not to remove the screws, as this could make it difficult to remove them in the future. Once the screws are removed, the cylinder will be easy to remove. Take out the Lock Barrel Upvc is a strong material, designed to ensure your family and you are secure. They are available in different styles and colours to suit any decor. These doors are also maintenance-free and thermally efficient. However, https://www.repairmywindowsanddoors.co.uk/poole-window-lock-repairs-near-me/ without their disadvantages. The locking point, also known as a barrel lock, may get faulty over time and must be replaced. This is a simple process however there are a few things to know before beginning. To remove the screw that is holding the lock cylinder, it is have to remove the door handle. It's typically a different color from the other screws and is situated on the edge of the door, just the keyhole. Remove the screw and store it in a safe location. Next, carefully slide out the door's outside and inside handles. Make sure to do this slowly and not too quickly as it could harm your uPVC door. Once you have removed the handles, use a screwdriver to disconnect the screws that are holding them to the frame of the door. This will let you better access the pins that keep the cylinder. You can then try to pull and wiggle the cylinder in order to see if this can loosen it. Once it does, pull it toward you and then out of the socket. After you have removed the old cylinder lock, it is important to replace it with a new one that is anti-snap as well as anti-bump protection. You can do this yourself if have the tools you need, or you can hire an expert locksmith to do it for you. This is a fairly simple task that will take 5 minutes to complete. Install the New Cylinder A door lock made of upvc can be damaged or broken in a variety of ways, for example, a tenant may have moved out and not returned the key, or the cylinder could have been damaged and is no longer functioning as it should. It is crucial to select the right size replacement for your upvc door lock. If the wrong one is installed, your upvc doors could be more vulnerable to the 'lock snapping method' which is responsible for 25 percent of burglaries. To avoid this, it is essential that the correct cylinder is used and the procedure for doing this is fairly simple and takes only five minutes. You will need a screwdriver to take off the screws that are connected to the faceplate on the handle and the cylinder, but once this is done it's a straightforward job to swap them over. Be sure to open the handle and have access to the lock cylinder on the faceplate side of the handle. This is to make sure that you are able to remove the lock cylinder without having to move the handle of the door and expose any internal components of the frame. The next step is to take the old cylinder out and measure it. You must know the overall length as well as the size of the cam, which moves to lock and unlock the door. This will help you find a new cylinder that's the same or even smaller. This is the most important part of the whole process. The cylinder should be flush with the handle and not extend more than 5mm away from it. Install the Handle It is not unusual for a upvc door lock to jam and this can be caused by something breaking inside the case that controls the bolts that retract into the strike or keep plate. Often this can be resolved by making an Allan key adjustment beneath the hinges of the door however occasionally this could put too much pressure on parts of the central case, so it is best to call a professional out. It is important to have quick and simple access to both sides when changing the handle. It is important to use the correct tools. It is recommended to place the door on its side to ensure that it doesn't close during this process. The first step is to loosen the screws that hold the handle in place using a screwdriver. Once these are loosened, the handle can be removed. After taking off the cylinder and the handle, it's now time to install the new handle. Make sure that the new handle fits your existing central cylinder and the cylinder. To determine the right size you need to measure the length of the spindle on the lever you currently own. Make sure that the screw fix centre on the handle is identical to the screw fix centre on your existing hole centre or cylinder. The replacement handles offered by Fab and Fixed are available in a variety of styles and are made to last. These handles are ideal for those looking to upgrade their upvc handle and improve home security. A good handle will ensure that your home is secure and safe and will not be easy for burglars to gain entry.