How to Do a Door Lock Change The change of your door lock is an easy and inexpensive way to increase the security of your home. However, the process is not for all. It requires a certain amount patience and expertise. It is necessary to replace the cylinder that is inside the knob's body. The cylinder is responsible for recognizing the key as it is inserted into the lock. Remove the old lock The first step in replacing the door lock is to take out the lock that was previously in use. It's a fairly simple process, but there are a few points to remember. Make sure the new lock fits the door. This will ensure that it fits properly and doesn't create a gap around the latch or deadbolt plug. Once you have removed the latch plate look for two bolts or screws on the inside of the casing, which connect the casing and halves of the lock together. Unscrew these with the help of a screwdriver, and then take the lock out of the door. If you are using a mortise locking system, there is an anchor screw that connects the handle to the spindle. Use a screwdriver to remove this screw, then remove the doorknobs. It is also recommended to take the deadbolt and latch plug from the hole in the door jamb. Install your new lock. If you are replacing a mortise you must take a measurement of the distance between the lock case and your door's edge to ensure that the new lock will fit. Several reasons might prompt you to change the door lock, for instance suspecting that someone else has the key or welcoming a new roommate. You can save money if you take the lock off yourself instead of hiring an expert. The process is easier than many people think and can be completed in a few minutes. Begin by removing the trim and handle from your door. With a flat screwdriver, pry off the trim. It should be possible to pull off the majority of it. In some instances, you may even be able to remove the handles completely. Then, check the handle for a tiny hole on the inside and insert a straightened paper clip into it. This will trigger the release mechanism, which allows you to take off the handle. Next, examine the interior side of the lock for a small tab and press it using a screwdriver that is flat. Once the spindle has been removed, you can then remove the cylinder and the housing. Selecting a new locking system There are many options to choose from when it comes to choosing the right lock. Consider different types of locks and select one that fits your door's style. Take into consideration the backset (the distance between the edge of the door and the center of the hole for the lock) and the cross bore (small hole along the edge of the door frame). Also, make sure to choose a lock that will be able to fit the door's thickness and swing. Most door locks are evaluated by BHMA and the American National Standards Institute to provide you with an idea of how well they are able to withstand the rigors of use and how difficult to disable or pick. A grade 3 lock may be the ideal choice for a tranquil apartment complex in a rural area, whereas locks of grade 1 may be more appropriate for a busy street near an open-air storefront. Most smart door locks require a digital key code to open. If you're concerned about hacking or other security issues you should consult a professional locksmith or your local police department for assistance. Replace the cylinder It is easy to replace damaged or broken door lock cylinder using a simple DIY project. The key is to select the right cylinder and follow the instructions that come with it. The first step is to take off the knob or handle if there is one, then unscrew the trim that is attached to the base of the lock cylinder by using a screwdriver. After the trim is removed, you can remove the screws that hold the cylinder in place using the flathead. The cylinder is then gently removed away from the door. Before you install the new cylinder, be sure it's the right length for the door you are using. Measure the distance from the center to the right and left sides of the cylinder using a tape measure. Purchase a new cylinder that has the same measurements. This will prevent cylinders from snapping when doors are hit or the key is stuck inside. Once you have a suitable replacement cylinder, place it in the door and turn the key. This will align the cylinder with the carrier which is typically on the outside of your lock. Then, loosen the set screws which should be a couple of turns in the head. https://www.repairmywindowsanddoors.co.uk/salisbury-window-lock-repairs-near-me/ will also need to loosen the screw at the door's edge which secures the case in the event that there is one. You can replace the cylinder that was used to lock your old lock with the new one by slipping it into the case, and then tightening the set screws. Installing the part that connects the cylinder to an indicator stem for a lock is also crucial. It is done by pulling three small tabs in the back of the cylindrical with needle-nosed pliers. Attach the bracket that is smaller to the back of the cylinder. You must then install the latch plate and strike plate, as well as the retaining rings fixed to the top of the lock the cylinder. Installing a new lock If you're replacing an existing lock, you should start by measuring the width of your door. Most locksets for residential use are designed to fit a door thickness of 1 3/8 - 3/4 inches. If your door is thicker than 1 3/8 to 1 3/4 inches, you'll require a stronger door kit. This will include longer screws and either an extended spindle extension or tail piece for door knobs. Most locks come with detailed instruction booklet to guide you through the installation of the new hardware. Be sure to read the instructions thoroughly before starting the process to make sure that you've followed all of the necessary steps. The guide will give you an idea of the amount of skill that is required to finish the task. If you're changing locks for the first time, you might consider asking a more experienced person for help. Before installing the new lock it is a good idea to cover the holes with tape the old hardware. This will keep the screws from slipping out of the holes and will protect any tile you might have put in the area. It will also protect your tiles from any damage caused by dirt, rust and grime. SECURAM Touch comes with an ad-hoc strip of masking tape or gaffer tape, however you can use any tape you own. After taking off the screws that connect the lock's interior to its exterior then remove the lock immediately. This should be done swiftly to avoid the lock from accidentally closing and damaging the mechanism. Fit the new latch bolt into the upper cross bore of the new lock, if it has one. Make sure you place it in the correct position, which is usually indicated by an illustration on the faceplate. Then, place the latch plate on top of the bolt and screw it into place. Finally, screw the deadbolt and strike plate into the door jamb. Test the deadbolt by throwing it a several times to make sure that it is extended all the way through the strike plate and is secured. Follow the instructions included in your electronic smart lock to program it. This involves downloading an application and creating an email address, verifying your identity, then accessing the wireless network to connect your device.