Replacing Lock on uPVC Door If you're looking to change the lock on your upvc door it is necessary to remove the existing handle and screw holes. This is usually easy to accomplish. The next step is to locate the screw which holds the lock barrel in place. It is usually colored differently than the other screws and located on the outside of the faceplate of the lock. Take the Cylinder off To change the lock on your doors made of upvc, you must first take off the cylinder that is currently in use. This is a relatively simple procedure that can be accomplished in around 30 minutes. All you require is a screwdriver. The Euro cylinder screw is usually located on the inside of the door next to the lock cylinder. The screw is typically colored differently from the other screws and is easy to identify. Take it off and store it in a safe location. Once the cylinder is removed, you can begin working on the removal of the handle. To accomplish this, you'll need to open the door wide enough so that you can observe the inside edge of the door and the faceplate on the outside of the lock. Remove https://www.repairmywindowsanddoors.co.uk/canterbury-window-lock-repairs-near-me/ that holds the handle to the door using a screwdriver. Once the screw is removed you should be capable of pulling the handle towards you, and the rest of the mechanism should be removed from the door. If you're having trouble getting the handle off the door frame, you may need to remove it. You can make use of a screwdriver or a drill to remove the handle. Be cautious not to pull or cross-thread it. If you are about to replace your cylinder, be sure that it is the correct size for the door you have. Cylinders are measured according to two factors: (a), the distance from the center of the Fixing Screw to the bottom of cylinder and (b) the distance between the hole of the keyhole and the edge of the lockplate. Take the handle off If your door handle made of upvc becomes stiff, loose or floppy The good news is that this is a fairly easy problem to fix. The multipoint lock cylinder or other internal parts within the door, in between the handle and frame, are typically the culprits. It is not uncommon for Upvc locks to get worn due to extreme weather conditions, heavy use or simply ageing and this can lead to issues with the locking or closing mechanism of the door. The cylinder may wear out and make it difficult to turn the key. The lock could also become stiff causing the handle to loosen. The cylinder can be repaired, and is a simple process. It can be done yourself, however you will require some knowledge about the mechanism's workings. You'll need to take off the handle to replace the cylinder. You'll need an screwdriver and a measuring tape for this. You will need to determine the size of your current cylinder since it will assist you in locating the correct replacement. The cylinder is what permits you to lock the upvc door. It is essential to order a replacement that is identical in size. To remove the old cylinder you'll need to remove the screws that are holding it. Be careful not to remove the screws, as this may make it difficult to remove them in the future. After the screws have been removed the cylinder will slide out easily. Remove the Lock Barrel uPVC doors are constructed with strong materials and are designed to keep your home safe and secure. They come in a wide variety of colours and styles that can suit any style of home. These doors are also maintenance-free and thermally efficient. However, they aren't without their drawbacks. As time passes, the barrel or locking point lock can become faulty and require replacement. This is a straightforward process however there are some things you should know before you start. You'll need to take off the door handle in order to reach the screw that holds the lock cylinder. It is typically colored differently than the other screws and can be found at the edges of the door, close to where the keyhole is located. Take out this screw and put it in a safe place. Then, carefully slide out the inside and outside door handles. Be sure you do this slowly and not too quickly as it could cause damage to your uPVC door. Once you have removed the handles, use a screwdriver to detach the screws that hold them to the frame of the door. This will let you better access the pins that hold the cylinder in position. Try to move the cylinder in order to see if this will loosen it. Once it comes loose then pull it back towards you and then out the socket. After you have removed the old lock cylinder it is essential to replace it with a new one that has anti-snap and anti-bump protection. It is best to let a professional locksmith do this for you, however you can do it yourself using the proper tools. This is a simple job that should take no more than five minutes. Install the New Cylinder A door lock made of upvc could be damaged or broken in many ways, for instance, a tenant could have moved out but not returned the key, or the cylinder might be damaged and is no longer functioning as it should. It is important to choose the correct size replacement for your door's upvc lock. If the wrong lock is installed, your upvc doors may be more vulnerable to the 'lock snapping technique that is responsible for 25% of burglaries. It is essential to put in the correct cylinder. The procedure is simple and takes less than five minutes. You will need a screwdriver to take off the screws that are connected to the faceplate of the handle and the cylinder. Once you have done this it's a simple job to swap them over. Before you get started ensure that the handle is in a position to open and that you have full access to the inside edge of the door and the handle's faceplate which holds the lock cylinder. This will allow you to easily remove the lock cylinder from the handle without having to move it, and expose the internal parts of the frame. Then, take out the old cylindrical device and determine its measurements. You will need to know its length and the diameter of the cylinder that is used to lock or unlock the door. This will help you to locate a replacement that is the same size or smaller. This is the most important part of the entire process. The cylinder should be flush with the handle, and not protrude more than 5mm beyond it. Install the Handle A lock made of upvc can stop working if something breaks within the case that controls the bolts which retract into the strike or keep plate. This can often be fixed by altering the Allan key underneath the hinges. However, this can cause stress on parts inside the casing in the middle and it is advised to call in a professional. It is crucial to have quick and easy access to both sides when you are changing the handle. It is important to use the right tools. It is also a good idea to prop the door open to ensure it doesn't shut during this procedure. The first step is to loosen the screws that keep the handle together using an screwdriver. After the screws are loose you can take off the handle. After the handle and cylinder are removed, it's now time to put in the new handle. Make sure the new handle is the correct dimension for the cylinder and hole in the center. To determine the correct size take a measurement of the spindle's length on the lever you currently own. Check that the screw fix centre on the handle is the same as the screw fix centre on your current hole centre or cylinder. The replacement handles from Fab and Fixed are available in a range of styles and are made to last. They are perfect for people who wish to upgrade their upvc handles and increase their home security. The right handle will make your home safe and secure, making it difficult for thieves to enter.