Replacing Lock on uPVC Door If you are looking to replace the lock on your upvc door you'll first need to remove the handle and screw holes. https://www.repairmywindowsanddoors.co.uk/weymouth-window-lock-repairs-near-me/ is usually easy to accomplish. The next step is to locate the screw that holds the barrel in place. This screw is typically a different colour to the screws that are used in other locks, and is located on the outside of the faceplate of the lock. Remove the Cylinder To change the locks on your Upvc doors first, you must remove the existing cylinder. This is a fairly easy process that can be completed within 30 minutes. All you need is an screwdriver. You'll need to locate the Euro fixing screw for the cylinder, which is usually on the inside edging of the door, next to the lock cylinder. The screw should be easily identifiable as it is usually different in colour from the rest of them. Take it off and store it in a safe place. After removing the cylinder, you can begin to remove the handle. To do this, you will have to open the door wide enough that you can see the inside edge of the door and the side of lock faceplate. Remove the screw that holds the handle to the door by using the screwdriver. After this screw is removed, you should be capable of pulling the handle towards you, and the rest of the mechanism will fall out of the door. If you're having difficulty getting the handle off, you may need to remove the screw that holds it to the stud inside the door frame. This can be accomplished using the aid of a screwdriver or drill, and you'll need to be careful not to cut the screw head or cross-thread the screw. When you are ready to replace your cylinder, ensure that it is the correct size for your door. Cylinders are measured based on two factors: (a), the distance from the center of the Fixing Screw to the bottom of cylinder and (b) the distance between the keyhole's hole the keyhole and the edge of the lockplate. Take the handle off If your door handle made of upvc becomes stiff or loose, the good news is that it is a fairly easy problem to fix. The multipoint lock cylinder or other internal components inside the door, in between the handle and frame, are often the culprits. The weather, the heavy use or ageing can cause the upvc locks to wear. This can cause problems with the locking and closing mechanisms of the door. If the cylinder is worn, it will often be difficult to turn the key and the lock could become stiff, causing the handle to drop. The cylinder is easily replaced, and it is a simple process. It is possible to do it yourself, though some understanding of how the mechanism operates will be required. You'll have to remove the handle in order to replace the cylinder. You will need an electric screwdriver and measuring tape to do this. You will need to know the dimensions of your current cylinder, since it will assist you order the correct replacement. The cylinder is what allows you to lock the door of your upvc. It is crucial to order a replacement that is identical in size. To remove the old cylinder, you'll have to remove the screws which hold it in place. Be careful not to remove the screws, as this could make it very difficult to remove them again in the future. Once the screws are removed the cylinder will pop out easily. Take out the Lock Barrel Upvc doors are constructed from extremely durable materials and are designed to ensure your home is safe and secure. They are available in a variety of designs and colors to match any style. These doors are also thermally efficient and maintenance-free. They do not come without a few drawbacks. As time passes, the barrel or locking point lock may fail and will require replacement. This is a straightforward process however there are some important things to consider before beginning. To access the screw holding the lock cylinder, it is have to take off your door handle. The screw is typically different from the other screws and is found near the keyhole on the door's edge. Remove the screw and store it in a safe location. Then, slowly move the outside and inside door handles. Make sure you do this slowly and not too quickly as it could harm your uPVC door. After you have removed the handles then, you can use a screwdriver and take out the screws that secure the handles to the door frame. This will allow you to gain access to the pins holding the cylinder. You can then try to pull and wiggle the cylinder in order to see if this can loosen it. If it does then pull it back towards you, and then pull it out of the socket. After you have removed the old lock cylinder it is essential to replace it with a new one that has anti-snap and anti-bump security. It is best to let an expert locksmith do this for you, but you can do it yourself using the appropriate tools. This is a relatively easy task that will take five minutes to complete. Install the New Cylinder A upvc lock can be damaged or broken in a number of different ways. For example, the cylinder may be damaged or isn't working as it should. Whatever the reason behind changing your Upvc lock, it's essential to choose the correct size replacement. This is because if the wrong one is installed, it could lead to your door being more vulnerable to a technique known as "lock snapping", which is responsible for 25 percent of burglaries. It is important to install the proper cylinder. The procedure is simple and takes only five minutes. To change the cylinder and handle faceplate, you will need to remove the screws that are attached to them. Before you get started be sure that the handle is opened and you have full access to the inside edge of the door and the side of the handle faceplate that holds the lock cylinder. This will enable you to easily remove the lock cylinder from the handle without having to move it and expose the internal components of the frame. The next step is to take the old cylinder out and measure it, you must determine the length of the cylinder and the diameter of the cam that rotates to lock and unlock the door. This will help you locate a replacement that is the same size or smaller and this is the most crucial part of the entire process. The cylinder should be flush with the handle and should not protrude more than 5mm beyond it. Install the Handle It is not uncommon for a door lock made of upvc to jam and this can be caused by something breaking inside the case that controls the bolts that retract into the strike or keep plate. This can often be solved by adjusting the Allan key under the hinges. However, this can cause stress on the parts within the centre casing and it is recommended to contact an expert. It is essential to have easy and quick access to both sides when you are changing the handle. Also, it is crucial to use the correct tools. It is also a good idea to prop the door open so that it doesn't shut during this procedure. The first step is to loosen the screws that keep the handle in place using a screwdriver. Once these are loosened the handle can then be removed. After removal of the cylinder as well as the handle, it's time to put in the new handle. Make sure the new handle fits your existing cylinder center and the cylinder. To determine the right size you need to measure the length of the spindle on the lever that you currently have. Make sure that the screw fix centre on the handle is the same as the screw fix centre of your existing hole centre or cylinder. Replacement handles from Fab and Fixed come in a variety of styles and are designed to last. They are ideal for those who want to upgrade their upvc handles and improve their home security. The correct handle will make your home safe and secure, and difficult for burglars to break into.