Replace Lock in UPVC Door If you have a Upvc door lock that's not working properly you should call in an expert locksmith. They are quick, efficient and finish the job to a high standard. It's not difficult to change the bar lock made of upvc. It's not difficult to change a upvc barrel lock. Removal of the Barrel Lock Upvc windows and doors are popular in a variety of houses. They let natural light be able to enter the home and can be opened with ease using the right key. The process of changing the barrel on an uPVC door is an easy task that takes only five minutes. If you've lost your keys, a tenant left and has not returned them, or the barrel of your lock is damaged, this is a quick solution. The first thing to do is remove the screws that hold the handles. The handles will be removed of the way to allow you to access the lock barrel screws. Be careful not to loosen the screws too much because this could cause damage to the handles or cause them to fall off while working. Once the screws are removed, locate the screw on the inside of the door that is holding the barrel lock in place. The screw is different in color from the other screws on your door and sticks out. Using the Phillips screwdriver, take out this screw. Then, grab the present key that is used for the lock and put it into the barrel. Then, turn it to the right as much as possible. This should free the barrel and make it easier to pull it out of the door. After you've loosen the screw and you're ready to break the support pins that hold the euro cylinder in place. You will need pliers with strength or mole grips do this. Grasp the protruding portion of the euro Cylinder and bend it up and down and from side to side. This will break the support pins holding it in place. Once the old cylinder is gone, you can begin the process of putting in the new one. First, you'll need to measure the size of the lock cylinder to make sure you have bought the correct replacement. This can be done by measuring the distance between the center of circular keyhole and the center of square spindle. The measurement should be taken from the upper spindle. Change the Cylinder The main locking mechanism is an euro cylinder. It is easy to replace and does not require a handyman or locksmith. If your lock isn't anti-snap or anti-bump it should be changed to one with this security built-in. They are very affordable and could save you money as well as inconvenience in the event that your locks have been damaged by these security threats. Open the door and then stand in front of it. This will allow you to reach the handle retaining screws by hand or with the appropriate tool. Let it loosen a bit, maybe just a quarter turn to begin the process. The cylinder should now be easily removed since the screw will stop holding it in position. The next step is to determine the size replacement cylinder you require. There are approximately 25 sizes available. You should bring your previous cylindrical when you buy one new to make sure it fits. If you're unsure of the dimensions, measure from the center of the screw hole to the end of cylinder. This is the only way to be sure you're getting the correct size cylinder for your Upvc doors. Once you have the replacement cylinder, place it into your door in reverse order to how you took out the old one. https://www.repairmywindowsanddoors.co.uk/colchester-window-lock-repairs-near-me/ could be tricky to align the lock cam but it is usually an issue with alignment, and will eventually be sorted out. Now you must screw the long securing screw back into its place. After that, you are able to test it to ensure that the cylinder is secure inside the door. Then, you can attach the handle back to the door and then test it again. If everything is functioning properly the cylinder lock on your doors made of upvc has been replaced and has added a layer of security to your home. Switching the Handle There are a variety of reasons the door handle or door knob can become loose. It can be due either to wear and tear of the handle or the square spindle inside the handle. In this scenario the door handle has to be replaced. Firstly it is important to make sure the door is propped open and won't close between taking off and replacing the handle. Remove the screws from the inside surface of the plate by using a screwdriver. This will remove the handle from the plate. Be careful not to lose the screws as they'll need to be re-screwed back into place later. After the handles have been removed, you will be able to access the cylinder lock inside the door. This will have a round or bulb shaped cylinder that is only found in multi-point locks on upvc doors as well as doors made of aluminium. The procedure for changing the cylinder is similar to that of changing the handle, but you'll need to take the old cylinder from the door, and replace with a new one. It is important to take into consideration the size of a replacement handle when selecting one. Make sure the handle is similar in size to the original because it will have to be able to be able to fit over the existing screws that keep the handle in place. A good place to start is by using a size matrix which will list the common sizes of replacement handles, as well as their keyhole center to handle plate distance. Consider changing your handles for your upvc doors to a higher security standard like a Sold Secure SS301 set or 2* Kitemark security handles. This will enhance the security of your home and make it easier to operate your door. The price of these sets may be slightly more expensive but the added peace of mind and security is well worth the cost. To constantly push the door handle upwards and downwards to shut and open it is not something you want to be doing. Changing the Lock The lock on your uPVC door can be a target for thieves. You may want to upgrade your uPVC door to a multipoint lock in order to make it more secure. This would include an open hook and a deadbolt to keep out burglars. A professional locksmith can assist you with this, however it is also possible to complete the work yourself. The process is simple and easy. You'll only require a few simple tools. The first step is to loosen the screws that hold the handle in place. By using a screwdriver you can remove the screws and place them in a secure place. Then, you can lift the handle to reveal the screw that is holding the cylinder. You can unscrew this screw and replace it a new one. Make sure the screw is of the same size as your original. It should be aligned properly with the barrel of the lock. Making changes to the lock on your uPVC door could appear daunting. You depend on it to secure your home, and mistakes could leave you without a way to unlock the door. If you know how, it's quite simple and is less expensive than calling an expert locksmith. You will need to remove the inner faceplate from the lock in order to change the lock. You'll need to look for the screws inside the door, and the retaining bolt outside the door. Once you have these screws in your hands, you can remove and replace the faceplate. You may need to change the lock of your uPVC door for a variety of reasons. It is possible to replace the lock on your uPVC door due to many reasons. Anyone with basic DIY skills can change the mechanism of a uPVC lock. If the lock is stuck, you will need to check the hinges in the mechanism. If the hinges have been lubricated then it is simple to repair. However, if you aren't confident doing this, it is best to call an expert.