Bi-Fold Door Repair If they are either internal or external, bi-fold doors provide a certain amount of flexibility that can be customized to suit any requirement. Like all other fixtures and fittings they can be subject to wear and wear and tear. Fortunately, it's not too difficult to restore them to good condition. With a little patience and some basic woodworking knowledge you can tackle a number of simple bi-fold door repair projects. Cracked Corners Bifold closet doors are usually light and are prone to cracking near the top and bottom pivot points. This typically occurs over time because of the natural deterioration of the wood in your home. Fortunately, this can be fixed by gluing and clamping the affected wood. The process is relatively easy and will reduce the expense of hiring a professional complete the task for you. Bifold doors are often unable to open or close easily. This is typically caused by a misalignment between the guides or pivot pins of the bifold doors. This can be caused by a slipped door or loose pivot pins or guides and is simple to fix it by a little effort. First, you should check the tracks or runners for obstructions or blockages. Dirt, sand, leaves fur, pet hair and everything else that gets into the running track can cause problems with the bifold door. Regular cleaning and lubrication for the tracks should keep them in good condition. If you notice that a door is leaning when closed, it may need to be trimmed. It is essential to use a circular type of saw for this because the doors aren't that thick. You should also be careful to avoid damaging or chipping the door veneer when trimming it. To do this, place the door on a sturdy workbench and mark an outline with a pencil. Cut the door with a circularsaw along the line. Another problem that often arises with a bifold door is that the doors be able to rub against carpeting when opened or shut. This could cause the seals to weaken, letting in draughts and making your home less energy efficient. This is a simple problem to fix. All you have to do is clean the seals using a non-abrasive solvent such as vinegar or mild dish detergent and then apply a silicone sealant to the damaged area. The issue will be solved when the sealant is dry. This should also help extend the longevity of your seals as well as the doors as a whole. Doors that aren't aligned If your bifold doors seem to be sticking or jamming when you attempt to open them or closed, it is a sign that they are not in alignment. It could also be an alarming security risk for your home. It is important to take action when you first detect it. If you delay repairs, you could cause damages that require more extensive and costly repair work. Adjusting the bifold door can be done relatively easily. Ensure that the track is clear of obstructions and clean. It is possible to use a brush or cloth to clean any dirt or debris that has built up over time. After the track has been cleaned, you can apply an oil spray made of silicone to lubricate the track and smooth out the movement of the door. Then, you'll need to adjust the pivot brackets to get your doors in the correct position. These brackets are located on the upper and lower corners of the door frame and are attached via screws. If your door is moving on the floor you can raise it by loosening the screws, then tightening them later. If it is moving away from the wall, you can lower it by loosening the screws and tightening them later. Continue making small adjustments until the doors are perfectly aligned. It's also important to check that the frame of the doors is secure. If the frame moves slightly it can cause gaps between the doors, which will allow air and water to be able to enter your home. This can also cause the hinges to move out of alignment which can result in doors that are uneven. If this happens, you will need to re-secure the frame. Also, make sure that the doors are on the same level as the floor. You'll have to adjust the hinge bolts if they're not in the proper position. This can be done by opening and shutting the doors. Then, use a spirit level and a screwdriver until the panels are all level. Shag Carpeting The bi-fold doors are designed to slide up and down, however they can sometimes scrape your floor or wall. This usually happens as a result of one or more pivot pins not aligned properly. This problem is often easy to fix. The pivot pin is located at the bottom of the bi-fold doors and is connected to a floor bracket. On top, a spring-mounted retaining pin connects to a sliding bracket that locks into the track. If your bi-fold door scrapes against the carpet, you can raise it by rotating the pivot pin at the bottom counterclockwise until it is at the proper level. The other reason you may be experiencing a shagging issue in your bi-fold doors is that the track that they slide on isn't level. This can be due to changing weather conditions, settling or shifting. If this is the case, you can adjust your tracks by loosening the screws that support the upper track bracket. Slide it up or down until it is at the same level as the lower track bracket. Bi-folding doors can be a problem if wood around the pivot pins is cracked. This is a problem that many doors suffer from and includes bifolds. You'll need C-clamps as well as a small amount of carpenter's adhesive to solve this. First, remove the door and then pry the pivot pin off using either pliers or a screwdriver. Spread the glue using a toothpick across the crack, clamp the door and allow it to dry for 3 to 4 hours. You should always repair your bi-fold doors by an expert, regardless of how small or severe the issue is. This will help prevent further damage and ensure that the door is operating properly. You can find an expert in your area by visiting the website of your door company. They will have a list of installers who have attended their certification workshop. Then, give them a call to schedule your bi-fold door repair appointment. Broken Slats Louvered closet doors allow air to circulate, prevent mildew from growing and make your clothes easier to see. Although they can be an attractive addition to homes, fixing or replacing them can be a challenge. Louver doors are constructed of slats that open and close to let in light, rain or wind. https://www.repairmywindowsanddoors.co.uk/bifold-door-repairs-caterham/ are made of polyurethane or wood moldings and used for doors, windows, or walls. Bifold doors do not all come with louvered slats, but those that do can become misaligned or break as time passes. You may think that you need to replace the door when a slat breaks. However, this is not required. You can repair the damaged slat by using a piece of fabric and carpenters glue. Begin by removing the closet door from the track and placing it on the floor or a set of saw horses in a way that the slats face up. You'll want to work on the door with it in this manner to avoid damaging or breaking the tracks or hinges. To remove a broken slat from a door put a claw-type hammer underneath each slat. Then, jerk the slat until it is separated. Once the slat has been removed, measure the space in which it was removed to determine the width and length of the replacement slat. Once you have the measurements then cut a piece foam board or cork to the same size that the area where the broken slat was removed. Apply a thick layer of carpenters' adhesive to the foamboard. Then place the fabric on the side of the board and smooth out wrinkles or creases as you go. Place the slat carefully into the slot in the door and attach it using nails, if needed. Once the glue is dry, you'll be able to rehang your bifold closet door.