How to Do a Door Lock Change The change of your door lock is a simple and inexpensive method to increase the security of your home. However, this process is not for everyone. It requires some expertise and perseverance. You must replace the cylinder, which is inside the knob's body. The cylinder is responsible for recognizing the key as it is put into the lock. Remove the old lock The first step in replacing a door lock is to take out the lock that was previously in use. It is a fairly straightforward process, however you should keep a few things in mind. Make sure your new lock fits your door. This will ensure that it fits securely and doesn't leave a gap in the deadbolt plug or latch. After removing the latch plate, you'll be required to search for two bolts or screws in the casing's interior which are holding the casing together with the two halves of the lock. Remove them with a screwdriver, then remove the lock from the door. If you have a mortise lock, there might be a set screw located at the base of the handle that binds it to the spindle. Remove the doorknobs by unscrewing this screw with the help of a screwdriver. You should also remove the latch and deadbolt plug from the hole in the door jamb. Then, you can put in your new lock. If you're replacing a mortise you must measure the distance between the lock case and the door edge to ensure that the new lock will fit. Several reasons might prompt you to replace the door lock, including being concerned that someone else may have the key, or you are welcoming a new roommate. You could save money if you remove the lock yourself instead of hiring for a professional. It's much simpler than you think and can be accomplished in a matter of minutes. Begin by getting rid of the handle and trim from the door. With a flat screwdriver pry off the trim. You should be able to twist off the majority of it. In some instances you might be able remove the handles completely. Next, examine the handle for a tiny pinhole on the interior side and insert a straightened paper clip into it. This will trigger the release mechanism, allowing you to remove the handle. Then, look on the interior side of the lock for another small tab that you can press using a screwdriver that is flat. After the spindle has been removed, you can take off the housing and the cylinder. Making a decision on a new locking system You have many options when it comes time to pick the right lock. Take a look at various types of locks, and select one that fits the style of your door. Take into consideration the backset (the distance between the edge of the door and the center of the lock hole) and the cross bore (small hole along the edge of the door frame). Also, be sure to select a lock that is able to fit the door thickness and swing. Most door locks have been graded by BHMA and the American National Standards Institute to provide you with an idea of how well they will withstand use and how difficult they are to disable or pick. A grade 3 lock may be the ideal choice for a tranquil apartment complex in the country, while locks that are grade 1 could be more suitable for a busy street near a storefront. Most smart door locks need a digital code to open. If you are concerned about hacking, or any other security concerns, speak to an expert locksmith. Replace the cylinder It is easy to replace damaged or broken door lock cylinder with a simple DIY project. It is crucial to choose the correct cylinder and follow all instructions. First, take off the knob or handle if it is present. Then with a screwdriver take off the trim around the lock cylinder. Once the trim has been removed, it is possible to remove the screws holding the cylinder in position with a flathead. The cylinder is then gently lifted out of the door. Before installing the new cylinder, you must make sure that it is the correct length for your door. Measure the distance from the center to the left and right sides of the cylinder with an instrument. Then, buy another cylinder that has the same measurements. This will help prevent cylinder snapping, which could happen when the door is kicked out or when the key gets stuck inside. If you have a replacement cylinder, place it into the door and turn the key. This will align the cylinder with the carriage that is usually located on the outside of the lock. https://www.repairmywindowsanddoors.co.uk/nottingham-window-lock-repairs-near-me/ can then loosen the set screws that should be a couple of turns in the head. If there is a screw on the exterior of the case that holds the door, you will need to remove it. You can replace the cylinder that was used to lock your old lock with the new one by slipping it into the case and tightening the set screws. You must also install the piece that connects the cylinder to the stem for the lock indicator and this can be done by pulling up three small tabs on back of the cylinder with needle-nose pliers. Then, you can connect the smaller bracket to the back of the cylinder. Then, you should reinstall the strike plate and latch plate as well as the retaining ring connected to the top of the lock cylinder. Installing a new lock If you're replacing an existing lock, you should start by measuring the width of your door. The majority of residential locksets come with a thickness of 3/8 to 1 3/4 inches. If your door is thicker it will require an extra-thick door kit that includes longer screws as well as longer tail pieces (for door knobs) or spindle extension (for deadbolts). The majority of locks come with a comprehensive installation guide to aid you. Before you begin, go through the instructions to make sure you've followed the steps. The manual will also give you an idea of the level of skill required to accomplish the task. You might want to seek out a friend who has worked with locks for assistance if you are changing a lock the first time. Before installing the new lock it is an excellent idea to put cover the holes with tape the old hardware. This will stop screws from falling through the holes, and also protect any tiles you have put in. It also shields your tiles from damage caused by rust, dirt and grime. SECURAM Touch comes with a strip of painter's tape, which is designed to be used for this purpose, but you can also use gaffer's or masking tape if you have it available. After taking off the screws that connect the lock's inner half to the exterior, pull the lock straight away. It is important to do this as quickly as possible to prevent the lock from closing itself in a way that could end up damage the mechanism. Fit the new latch bolt into the upper cross bore of the new lock if it has one. Make sure to place it in the proper position, which will be indicated by an arrow. Then, you can screw the latch plate onto the bolt. Finally, screw in the deadbolt and strike plate into the door jamb. Check the deadbolt several times, throwing it around to make sure it extends into the strike plate. Follow the steps included with your electronic smart lock to program it. This involves downloading an application and creating an email address, verifying your identity, then accessing the wireless network to add your device.