Anomalous diffusion dynamics in confined nanoenvironments govern the macroscale properties and interactions of many biophysical and material systems. Currently, it is difficult to quantitatively link the nanoscale structure of porous media to anomalous diffusion within them. Fluorescence correlation spectroscopy super-resolution optical fluctuation imaging (fcsSOFI) has been shown to extract nanoscale structure and Brownian diffusion dynamics within gels, liquid crystals, and polymers, but has limitations which hinder its wider application to more diverse, biophysically-relevant datasets. Here, we parallelize the least-squares curve fitting step on a GPU improving computation times by up to a factor of 40, implement anomalous diffusion and two-component Brownian diffusion models, and make fcsSOFI more accessible by packaging it in a user-friendly GUI. We apply fcsSOFI to simulations of the protein fibrinogen diffusing in polyacrylamide of varying matrix densities and super-resolve locations where slower, anomalous diffusion occurs within smaller, confined pores. The improvements to fcsSOFI in speed, scope, and usability will allow for the wider adoption of super-resolution correlation analysis to diverse research topics.To increase the manufacturing throughput and lower the cost of silicon photonics packaging, an alignment tolerant approach is required to simplify the process of fiber-to-chip coupling. Here, we demonstrate an alignment-tolerant expanded beam backside coupling interface (in the O-band) for silicon photonics by monolithically integrating microlenses on the backside of the chip. After expanding the diffracted optical beam from a TE-mode grating through the bulk silicon substrate, the beam is collimated with the aid of microlenses resulting in an increased coupling tolerance to lateral and longitudinal misalignment. With an expanded beam diameter of 32 μm, a ±7 μm lateral and a ±0.6° angular fiber-to-microlens 1-dB alignment tolerance is demonstrated at the wavelength of 1310 nm. Also, a large 300 μm longitudinal alignment tolerance with a 0.2 dB drop in coupling efficiency is obtained when the collimated beam from the microlens is coupled into a thermally expanded core single-mode fiber.Large effect pigments, widely used in various fields of industrial applications, produce characteristic visual textures known as sparkle and graininess, which need to be quantified by objective or subjective methods. The development of preliminary measurement scales for sparkle and graininess, whose recommendation is now under discussion in the International Commission on Illumination (CIE), is described in this article. These scales are absolute, linear and traceable to standards of optical radiation metrology. The main purpose of this article is to justify the convenience of adopting these preliminary measurements scales, showing clear evidence that they correlate well with subjective evaluations. Before standardization, these scales need to be validated with more experimental data, including different specimens and experimental systems from other research groups.Volumetric light transport is a pervasive physical phenomenon, and therefore its accurate simulation is important for a broad array of disciplines. While suitable mathematical models for computing the transport are now available, obtaining the necessary material parameters needed to drive such simulations is a challenging task direct measurements of these parameters from material samples are seldom possible. Building on the inverse scattering paradigm, we present a novel measurement approach which indirectly infers the transport parameters from extrinsic observations of multiple-scattered radiance. The novelty of the proposed approach lies in replacing structured illumination with a structured reflector bonded to the sample, and a robust fitting procedure that largely compensates for potential systematic errors in the calibration of the setup. We show the feasibility of our approach by validating simulations of complex 3D compositions of the measured materials against physical prints, using photo-polymer resins. As presented in this paper, our technique yields colorspace data suitable for accurate appearance reproduction in the area of 3D printing.  https://www.selleckchem.com/products/vt103.html  Beyond that, and without fundamental changes to the basic measurement methodology, it could equally well be used to obtain spectral measurements that are useful for other application areas.Perfect absorbers are highly desired in many engineering and military applications, including radar cross section (RCS) reduction, cloaking devices, and sensor detectors. However, most types of present absorbers can only absorb space propagation waves, yet absorption for the surface wave (SW) has not been researched intensively. In reality, when the space wave illuminates on the metal under large oblique angles, surface waves can be excited on the interface between metal and dielectric and thus would increase the RCS and influence the stealth performance. Here, based on the wave vector and impedance matching theories, we propose a broadband absorber for the surface wave under spoof surface plasmon polariton (SSPP) mode. The former theory ensures that surface waves can enter the absorber efficiently, and the latter guarantees perfect absorption. The experimental results indicate that our absorber can achieve a broadband (9.4-18 GHz) performance with an absorption ratio better than 90%, which is in great agreement with the simulations. Therefore, our device can be applied in RCS reduction for the metal devices, antenna array decoupling and many other applications. Also, this work provides a unique methodology to design new types of broadband surface wave absorbers.Multifunctional metasurfaces have exhibited considerable abilities of manipulating electromagnetic (EM) waves, especially in full-space manipulation. However, most works are implemented with functions controlled by polarization or frequency and seldom involve the incidence angle. Herein, we propose a multifunctional full-space metasurface controlled by frequency, polarization and incidence angle. A meta-atom is firstly designed. When EM waves illumine normally in the C-band, it possesses the characteristic of asymmetric transmission with high-efficient polarization conversion. In the Ku-band, both x- and y-polarized EM waves along both sides will be reflected and achieve broadband and high-efficient cross-polarization conversion. Also, when illumined obliquely, both sides can achieve efficient retroreflection at a certain frequency. As a proof of concept, a metasurface consisting of the above meta-atoms is configured as a dual orbital angular momentum (OAM) vortex beam generator and different beam deflector when illumined normally.