DNA walkers, one of the artificial molecular machines which are constructed via smart synthetic DNA, have attracted rapidly growing attention from researchers in the biosensing field. In this work, we design an Exonuclease III (Exo III)-aided target-aptamer binding recycling (ETBR) activated bipedal DNA machine for highly sensitive electrochemical detection of antibiotics. To the best of our knowledge, this is the first time that a bipedal DNA machine has been applied in electrochemical sensing for antibiotics. On the one hand, the bipedal DNA walker exceeds the conventional single swing arm DNA walker in terms of walking efficiency and stability. On the other hand, the ETBR strategy, along with efficient strand displacement amplification via stepwise movement of a bipedal DNA walker significantly promotes the signal amplification efficiency. Under optimal conditions, this bipedal DNA machine possesses a detection limit of 7.1 fM within a linear detection range from 10 fM to 100 pM. Moreover, this electrochemical biosensor is expected to detect a wide variety of analytes using the corresponding target recognition probes. Thus, our proposed strategy offers a highly efficient, stable and practical platform for small molecule analysis.The thickness of monolayers is a fundamental property of two-dimensional (2D) materials that has not found the necessary attention. It plays a crucial role in their mechanical behavior, the determination of related physical properties such as heat transfer, and especially the properties of multilayer systems. Measurements of the thickness of free-standing monolayers are widely lacking and notoriously too large. Consistent thicknesses have been reported for single layers of graphene, boronitrene, and SiC derived from interlayer spacing measured by X-ray diffraction in multilayer systems, first-principles calculations of the interlayer spacing, and tabulated van der Waals (vdW) diameters.  https://www.selleckchem.com/products/gw4869.html  Furthermore, the electron density-based volume model agrees with the geometric slab model for graphene and boronitrene. For other single-atom monolayers DFT calculations and molecular dynamics (MD) simulations deliver interlayer distances that are often much smaller than the vdW diameter, owing to further electrostatic and (weak) covalent interlayer interaction. Monolayers strongly bonded to a surface also show this effect. If only weak vdW forces exist, the vdW diameter delivers a reasonable thickness not only for free-standing monolayers but also for few-layer systems and adsorbed monolayers. Adding the usually known corrugation effect of buckled or puckered monolayers to the vdW diameter delivers an upper limit of the monolayer thickness. The study presents a reference database of thickness values for elemental and binary group-IV and group-V monolayers, as well as binary III-V and IV-VI compounds.Acute and chronic wounds cause severe physical trauma to patients and also bring an immense socio-economic burden. Hydrogels are considered to be effective wound dressings. Polysaccharides possessing distinctive properties such as biocompatibility, biodegradability, and nontoxicity are promising candidates to structure hydrogels for wound healing. Polysaccharide-based hydrogels can provide suitable moisture for the wound and act as a shield against bacteria. Adequate mechanical properties, degradability, and therapeutic agent controlled release of polysaccharide-based hydrogels have been already characterized for effective utilization. This review presented several crucial design considerations about hydrogels for wound healing, and the current state of polysaccharide (chitosan, alginate, hyaluronic acid, cellulose, dextran, and starch)-based hydrogels as wound dressings was also summarized. The commonly used crosslinking techniques, including physical, chemical, and enzymatic crosslinking, are discussed in detail. Finally, we outline the challenges and perspectives about the improvement of polysaccharide-based hydrogels.Mixed-dimension van der Waals (vdW) p-n heterojunction photodiodes have inspired worldwide efforts to combine the excellent properties of 2D materials and traditional semiconductors without consideration of lattice mismatch. However, owing to the scarcity of intrinsic p-type semiconductors and insufficient optical absorption of the few layer 2D materials, a high performance photovoltaic device based on a vdW heterojunction is still lacking. Here, a novel mixed-dimension vdW heterojunction consisting of 1D p-type Se nanotubes and a 2D flexible n-type InSe nanosheet is proposed by a facile method, and the device shows excellent photovoltaic characteristics. Due to the superior properties of the hybrid p-n junction, the mix-dimensional van der Waals heterojunction exhibited high on/off ratios (103) at a relatively weak light intensity of 3 mW cm-2. And a broadband self-powered photodetector ranging from the UV to visible region is achieved. The highest responsivity of the device could reach up to 110 mA W-1 without an external energy supply. This value is comparable to that of the pristine Se device at 5 V and InSe device at 0.1 V, respectively. Furthermore, the response speed is enhanced by one order of magnitude over the single Se or InSe device even at a bias voltage. This work paves a new way for the further development of high performance, low cost, and energy-efficient photodetectors by using mixed-dimensional vdW heterostructures.A liquid/liquid interfacial method is used to synthesize a conjugated porous polymer nanofilm with a large domain size. Copper-catalyzed azide-alkyne cycloaddition between a triangular terminal alkyne and azide monomers at a water/dichloromethane interface generates a 1,2,3-triazole-linked polymer nanofilm featuring a large aspect ratio and robustness against heat and pH.To understand the relationship between the work function and structural properties of sufficiently expanded triangular defects (size ∼250 μm) in the 4H-SiC epitaxial layer, Kelvin probe force microscopy (KPFM) and spectroscopic [micro-Raman spectroscopy and photoluminescence (PL)] analyses were performed. Spectroscopic analysis demonstrated that the triangular defects mostly comprise the 3C polytypes and that it experiences internal stress, defects, and defect-induced carrier generation. The distinguishable areas in the triangular defects had surface potential values different from those of the 4H-SiC matrix; this could be explained by the work function difference, which arises from variations in the electron affinity of the 3C polytype as well as the positional variations of the Fermi energy level in terms of electron concentration. In addition, tensile-stress-induced surface disorder leading to variations in electron affinity was discussed. The mechanical properties of the triangular defects measured by a nanoindenter were significantly deteriorated because of many dislocation arrays and stacking faults with many broken and/or strained bonds.